Skip to main content
Product Review
essl
essl bg100 ti
boom barrier india
bending arm barrier
basement parking gate

eSSL BG100 TI Review: Bending-Arm Boom Barrier India

BG100 TI bending-arm barrier: 5 m folding arm, 6-sec operation, IP55, 30 lakh MCBF, photocell plus Wiegand links. India review.

Quick answer

BG100 TI folds a 5 m arm around low basement ceilings at 6 seconds a cycle with IP55 sealing and 30 lakh cycle duty. Dry-contact plus Wiegand links suit apartment and office parking. It fits basements, stilt floors and ramped entries. Straight-arm plazas compare the BG100 TII.

By MegaMind Technosoft Team · Biometric & Access Control Specialists 9 min read
Share:
eSSL BG100 TI bending-arm boom barrier at an Indian basement parking entry
eSSL BG100 TI bending-arm boom barrier at an Indian basement parking entry

Key takeaways

  • BG100 TI bending-arm barrier: 5 m folding arm, 6-sec operation, IP55, 30 lakh MCBF, photocell plus Wiegand links. India review.
  • Start With Ramp-Clearance History
  • Folding Arm That Clears Low Ceilings
  • Photocell and Air-Switch Safety Line
  • Dry-Contact Control With Wiegand Reader Links

This eSSL BG100 TI guide starts where the site survey starts. A Gurugram condo ran its basement entry through a straight-arm barrier and a guard with a remote. The ramp ceiling sat low over the second bend, so the straight arm could only rise halfway before scraping concrete; guards started holding it open through evening rush while SUVs rolled under a half-raised arm. One monsoon evening a delivery van clipped the hanging tip and snapped the arm mount. Residents parked the broken arm against the wall for a week while the entry ran fully open. The condo replaced the unit with a BG100 TI bending-arm barrier: a 5 m aluminium arm that folds 2.5 m straight plus 2.5 m bending, clearing the low ceiling on its 6-second rise, with photocell input watching the ramp bend and auto-close timers shutting the lane after each car.

What follows is a field review of the BG100 TI: an automatic plus manual bending-arm boom barrier with 5 m maximum boom in 2.5 m straight plus 2.5 m bending sections, aluminium arm with boom-rest stand, 6-second up and down time, IP55 protection, minus 20 to plus 50 degree band, dry-contact control, photocell and air-switch inputs, alarm-lamp output, optional access-control panel plus standalone control plus button, remote control to 25 m, STOP UP DOWN panel buttons, optional bumping bounce-back, 1 to 99 second auto-closing, manual release with double safety limit switches, 30 lakh MCBF intensive duty rating, optional traffic-light interface, and Wiegand RFID plus biometric compatibility. Every figure comes from the verified catalogue technical section.

Start With Ramp-Clearance History

Four questions decide bending-arm barriers before you compare cabinet brochures.

  1. Does a straight arm scrape the ceiling, sprinkler line or ramp bend on its rise?
  2. Do guards hold the arm open through rush because cycles feel too slow or too exposed?
  3. Do vans clip arm tips at the bend where sight lines break around concrete columns?
  4. Can the site give the island a level base, loop wiring cuts and UPS-backed power with photocell posts?

Low ceilings plus held-open history points here. Open plazas stay straight; the inspection pillar maps the full gate bench from lobbies to perimeters.

Folding Arm That Clears Low Ceilings

The 5 m aluminium arm splits into a 2.5 m straight root plus a 2.5 m bending tip joined by a linkage that folds as the shaft rises. Under a 2.6 m basement slab the tip tucks back over the root instead of grinding sprinklers, so the cabinet can sit close to the ramp bend where guards actually see plates. Aluminium keeps the moving mass low, which protects the gearbox when a nervous driver nudges the arm at walking pace. The supplied boom-rest stand takes the tip load at closed position, so overnight wind push and cleaner carts do not bend the linkage out of true. Set the rest-stand height during install with a spirit level, not by eye; a 10 mm mismatch loads one hinge and starts the wobble that later reads as motor wear.

Where it misses: folding linkages need periodic pin checks that straight arms forgive. Skip half-yearly hinge inspection and the joint develops play, which shows up as tip shudder on windy days. Keep a small spares pouch of linkage pins and nyloc nuts at the control room; they cost little and stop a three-day open lane.

Six-Second Cycle With Auto-Close Timers

Six seconds up and six down keeps a 40-car resident peak moving without the lane feeling like a toll plaza. The 1 to 99 second auto-closing timer shuts the lane after each car, which ends the held-open habit that made the old entry run open all evening. Set resident lanes near 3 seconds and visitor lanes near 8 seconds so guests clear the photocell line before the arm starts down. STOP UP DOWN panel buttons give the guard direct hold control during ambulance or fire-tender movement without pulling power. Log timer changes with dates on the panel door card; undocumented tweaks are the usual reason a lane starts closing on slow SUVs.

Photocell and Air-Switch Safety Line

Photocell input watches the ramp bend where columns break sight lines, holding the arm up while a car still sits in the beam. Air-switch input on the arm edge stops and reverses on contact pressure, which covers the child running behind an SUV that the photocell beam misses. Alarm-lamp output flashes during movement so pedestrians on the ramp stairs time their crossing instead of ducking under a moving tip. Optional bounce-back lifts the arm on obstruction for sites where school vans and senior-citizen cars share the lane. Test both inputs monthly with a carton, not a hand; guards trust a safety line they have seen stop the arm.

Where it fails: photocells drift out of alignment after a cleaner knocks a post. Unaligned beams either hold the lane open all day or miss low cars entirely. Fix posts on concrete stubs with caged conduit, align at bumper height, and paint a witness mark across bracket and post so drift shows in one glance.

Manual Release and Double Limit Switches

Manual release frees the arm for hand operation during power cuts, so the basement does not trap cars when the grid trips. Double safety limit switches cut the motor at both travel ends, which stops the gearbox from hammering its stops after a voltage dip resets the controller. Keep the release key on a tagged hook inside the control room, not in a locked drawer the night guard cannot open. Drill the release once a quarter with the actual guard on duty; a key nobody has turned is the same as no release.

Dry-contact control accepts open commands from any panel, loop detector or push button already on site, so the barrier inherits pass truth instead of building a second list. Wiegand compatibility takes RFID readers and biometric units for resident and staff lanes, while visitor cars stay on guard-button or visitor management QR release. Remote control to 25 m covers the guard cabin to island gap on wide ramps without trenching a new cable. Run reader cable in separate conduit from motor mains; induced noise on shared runs is the classic cause of missed tags at peak hour.

Traffic-Light Interface and Alarm Lamp

Optional traffic-light interface drives red and green heads at the ramp mouth, which stops the two-car face-off inside single-lane basements. The alarm-lamp output doubles as the movement warning during night hours when the light heads switch to blink. Pair the heads through access control timing so green only shows after the arm reaches full up; early green sends cars into a half-raised tip. For tight ramps add the BB radar as a presence check above the loop, since loops miss high-chassis vehicles that stop short of the cut.

BG100 TI vs Straight-Arm vs Fencing Options

Three barrier answers for three ramp shapes. BG100 TI folds under low slabs. BG100 TII runs a straight arm across open plazas where height is free. BG 108 covers budget single lanes where traffic is light and duty stays low.

BarrierArmCycleBest fitWatch out for
BG100 TI5 m folding6 secBasements, stilt floorsHinge pins need checks
BG100 TIIStraight arm6 sec classOpen plazas, campusesNeeds full rise height
BG 108Standard armStandardLow-traffic gatesLight duty only

Sizing Maths for a Basement Lane

Cars per hour set the lane count, not total flats. A 200-flat condo pushes about 60 cars in the 8:30 to 9:30 window; at 10 cars a minute the single TI lane clears them inside six minutes with timers near 3 seconds. Add a second lane when the peak crosses 90 cars an hour or when visitor taxis queue behind residents. Count with a clicker across one weekday plus one weekend evening before ordering; brochure maths never matches school-van weeks.

Specs That Decide the Purchase

IP55 housing with a minus 20 to plus 50 degree band suits rain-washed ramps and hot stilt floors without a canopy rethink. The 30 lakh MCBF intensive-duty rating fits apartment peaks that cycle hundreds of times daily; light-duty arms cost less and die sooner on the same roster. Optional access panel, standalone control and button modes let one cabinet serve resident RFID by day and guard-button operation during network outages. Spares to stock: linkage pins, a photocell pair and one alarm lamp; each is cheap and each strands the lane when missing.

Site Conditions That Change the Answer

Basement ramps with bends need the folding tip plus a photocell post at the blind column; open villa gates can run straight arms with simple loops. Hospitals keep bounce-back on for ambulance-adjacent lanes, while office parks pair the barrier with attendance exports for staff vehicle logs. Multi-tower condos sync lane logic through api-integrations so one tag update reaches every island the same night. Outdoor plaza entries without height limits step to BGL 100 straight-arm builds; high-security campuses add BG180 BDC brushless DC duty where cycles run all day.

Power, Island and Loop Layout

Pour a raised concrete island with caged conduit before the cabinet arrives; surface-run cable across a basement ramp lasts one monsoon. Cut the safety loop clear of the arm drop line and seal the slot against oil wash; cracked loop sealant is the usual reason a lane starts missing cars. Battery backup should carry the controller plus photocell through short cuts so the arm never freezes mid-travel; size it for logic and detection, not just the motor. Mount cabinets, controllers and detectors from the boom-barrier-accessories bench on the same island so one guard sees every fault LED without walking the ramp.

The Half Buyers Forget: Logs and Visitor Flow

Barrier hardware proves movement, but park managers ask for entries. Link lane events into controllers and mobile-application passes so resident tags, guest QR codes and guard overrides land in one dated log. Visitor cars booked through visitor management should release the arm on QR scan with an 8-second close; manual-button visitor entries need the same log line or billing disputes follow. Demand one combined barrier-plus-visitor report from trial weeks; buyers file movements alongside guard rosters instead of trusting totals.

What a Bending-Arm Deployment Looks Like

Survey the ramp with a tape at the lowest slab point, the bend column and the island width before signing; folding arms forgive height but not narrow islands. Raise a per-lane BOQ with cabinet, 5 m folding arm plus rest stand, photocell pair, loop detector, panel wiring, UPS-backed power, island civil work and red-green heads. Anchor the cabinet to torque sheets, align the photocell at bumper height, set resident timers near 3 seconds and visitor timers near 8 seconds, then run one live evening peak before handover. Settle weekly with exception sheets and same-day reasons. Sign AMC after one full monsoon plus one clean visitor-log audit.

Lane discipline for the eSSL BG100 TI follows the ISO quality management overview; keep the loop-detector log with the gate register.

Want the short version of every guide like this?

Get practical buying tips, product comparisons and security advice — plus a free consultation when you're ready to compare options.

BG100 TI (BG100 TI)
View BG100 TI

BG100 TI

In Stock

eSSL BG100 TI is a 5-metre bending-arm boom barrier with a 2.5 m straight section and 2.5 m bending section. It has an aluminium arm, 6-second opening/closing time, IP55 protection, automatic/manual operating modes, dry-contact control and interfaces for photocell, air switch and optional access-control equipment.

  • Auth
  • Standard Connectivity

Frequently Asked Questions — eSSL BG100 TI Review: Bending-Arm Boom Barrier India

Pan-India Enterprise Security Engineers

Need help implementing this? — eSSL BG100 TI Review: Bending-Arm Boom Barrier India

Tell us your requirement and our certified security engineers will configure the exact hardware, cloud attendance software, and installation plan — with pan-India AMC warranty.

Genuine Hardware Pan-India Installation 1-Business-Day Quote